AC repair
Furnace & heating
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateFast, Reliable Furnace Repair Across Irving
When the heat stops in January, the question isn’t whether you can tough it out. It’s who can get to your equipment and get it running again without guessing. We work in Irving all the time, and our furnace repair team knows the layouts here: the post-war tract homes of south Irving with their original equipment, and the newer mid-rise condos out toward Las Colinas and Valley Ranch. That mix matters, because a furnace in a 60-year-old house acts nothing like one in a 2015 condo.
Call (855) 759-1429. We answer 24/7. Fast dispatch from 7am to 7pm. Estimates are free, and the price is set per job by a written estimate, never a surprise on the invoice.
Why Irving Homeowners Call Carrollton AC Repair for Furnace Repair
Irving sits at a strange crossroads. You’ve got 1950s and 1970s tract housing in the south, and high-rise towers packed against the DFW Airport edge. A technician who only knows one kind of building is only useful half the time here. That’s the gap we fill.
We service nine of the most-installed brands in the industry – Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. When we walk up to a Rheem or a York in a Valley Ranch condo, we already know how it’s put together. No fumbling through a manual while your house gets cold.
Our technicians have up to experience, and they’re HVAC specialists only. Not handymen splitting attention between plumbing and roofing. Heating and cooling, full stop.
Response time to Irving is quick because we know the roads, and we know the neighborhoods. If you’re off Story Road or tucked into one of the older south Irving blocks, we’ve been there before. No hunting for addresses.
Styles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
Heating Repair in Irving
Heating Repair in Irving often means dealing with equipment that’s been pushed hard through a long cooling season and then asked to switch over fast. North Texas doesn’t give your furnace much of a break-in period. The shoulder seasons are short. When you finally fire it up in November, that’s the moment weak components show themselves.
Common calls: a blower motor that’s been stressed by a clogged coil, a gas valve that won’t open, or an ignitor that’s simply done. Costs run $150 – $700 for most jobs, and the written estimate locks the final number before we touch anything.
What a Heating Repair Visit Involves
We isolate power, check the heat exchanger and blower motor, test the capacitor, and verify the gas train before restarting. If your furnace has been sitting dormant, the inspection matters as much as the fix. A component that failed quietly over summer can turn into a safety issue the moment the burners light.
When to Call Before the First Cold Snap
If your system short-cycled last winter, or if a fall storm knocked out power to the equipment, call before you need it. A tripped breaker that gets reset without drying and testing the controls is how small problems become expensive ones.
Boiler Repair in Irving
Boiler Repair in Irving comes up less often than forced-air work, but the older homes in south Irving still have a few of them, and when a boiler fails in January the house goes cold fast. A boiler fault usually traces to a circulator, a pressure control, or a control board that took a surge. The water side needs checking too, because scale and sediment build up over decades.
Most boiler repair jobs in Irving land in the $150 – $700 range. If the problem is deeper, you’ll hear it from us honestly, with the written estimate to back it up.
Boiler Controls and the Surge Problem
Boilers are notoriously sensitive to power quality. A DFW-area storm that rolls through and flickers the lights can leave a control board or a pressure switch confused, and the boiler locks out. We test the controls before assuming the whole unit needs replacing.
Older Homes and Water-Side Issues
In the 1950s and 1970s housing stock, original piping and old radiators mean the water side needs attention alongside the burner. Sediment that settles over decades restricts flow and makes the boiler work harder than it should. A quiet but expensive problem.
Trusted Brands We Service in Irving
We service Rheem, York, Daikin, Bryant, and the rest of the nine brands we cover across Irving. No parts stock claim, no warehouse talk. When a part is needed, we identify it fast and get it. Our technicians arrive already familiar with the platform, which cuts the diagnostic time and gets your heat back on. Whether your equipment is a Rheem furnace in a Valley Ranch condo or a York boiler in an older south Irving home, the approach is the same: understand the system, then fix what’s actually wrong. Brand-agnostic, and we mean it. The recommendation follows the equipment, not a dealer deal.
Common Furnace Repair Problems We See in Irving Homes
- Flooded condensers from street flooding in south Irving’s tight side yards. The low-set coils take on water when a summer storm dumps fast, and the waterlogged controls and tripped breaker can’t simply be reset. That breaker has to stay off until the unit is dried and tested.
- Power-surge damage after DFW-area storms. A capacitor or control board can fail invisibly, especially in older Irving homes where the furnace shares a circuit with other appliances. The system may power up but not heat.
- Hail-dented fins and debris-clogged coils on Las Colinas rooftop units. Restricted airflow raises static pressure and stresses the blower motor. The unit runs, but it runs hot.
- Age-related heat exchanger cracks in 1950s-70s south Irving homes. These often turn up after a failed restart, and the safety inspection has to come before any further use. A cracked exchanger is not a repair you put off.
See the difference
Before
After
Before
After
Before
AfterPricing for Furnace Repair in Irving, TX
Furnace repair in Irving typically runs $150 – $700, depending on what’s failed and how deep the diagnostic goes. A simple ignitor or capacitor sits at the low end. A control board, a blower motor, or a heat exchanger inspection that leads to a replacement climbs toward the top of the range. The estimate is free, and it’s written down before any work starts, so the final price is the number you agreed to.
What drives cost in Irving: the age of the equipment, whether the problem is electrical or mechanical, and how accessible the unit is. A furnace buried in a tight south Irving attic closet takes more time than a packaged unit you can reach. The written estimate reflects that up front.
| Service | Typical Estimated Range |
|---|---|
| Furnace Repair | $150 – $700 |
| Heating Repair | $150 – $700 |
| Boiler Repair | $150 – $700 |
These are typical estimates. The written estimate sets the final price on every job.
We Also Serve Cities Near Irving
Irving is home base for this page, but the same furnace repair work reaches the neighboring cities too. We serve Carrollton, Dallas, Grand Prairie, and Lewisville. If you’re in Irving proper or just outside the line, the call is the same, and the process is the same – a free estimate, a clear answer on what’s wrong, and a written price before work begins.
Serving Irving, TX – Our Local Coverage Area
We serve Irving and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Irving
No. If water entered the condenser coil or the controls, resetting the breaker can short the system or create a shock and fire hazard. The unit needs to be dried, inspected, and tested first. Call (855) 759-1429 – estimates are free, and we’ll tell you what the restart actually requires.
Check whether the breaker tripped, look at the fins for dents, and note any debris clogging the coil. Don’t reset the breaker if there’s visible damage. Hail-dented fins raise static pressure and stress the blower, so a diagnostic matters. Call (855) 759-1429 for an exact quote.
A surge often damages the capacitor or the control board, and a failing component causes the system to cycle on and off. The furnace may run but never satisfy the thermostat. Call (855) 759-1429 – most of these fixes fall in the $150 – $700 range, and estimates are free.
Only with a properly wired transfer switch. Generator backfeed or improper transfer switch wiring causes erratic thermostat behavior and furnace lockouts, and it can be dangerous to the equipment. Have it verified before relying on generator power. Call (855) 759-1429 for a diagnostic.
A yellow or flickering flame, soot around the burners, a strange smell, or a furnace that won’t restart after a storm are all warning signs. In the 1950s-70s housing stock, these cracks are age-related and need a safety inspection before any further use. Call (855) 759-1429. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Get Your Heat Back On in Irving
Storm damage, a failed restart, or a furnace that’s simply given out – the call is the same. Call (855) 759-1429. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Free estimates, upfront written pricing, and a technician who already knows your brand. Repair or replace, you’ll get the honest answer.
Written by the team at Carrollton AC Repair.